8′ x 15′ Park Industries Titan 1600, Stone Cutting CNC Router, 2011 – Available Immediately

The information contained in the document was correct at the time it was produced. Park Industries reserves the right to make additions, deletions and alternations to information described, depicted or represented with- out prior notice.

Effective Work Area:
1800 – Router only spindle: 15′ 10″ x 8′ 21⁄2”
1800 – Router with saw blade option: 14′ 6″ x 8′ 21⁄2” 1600
Router-Only Spindle: 15′ 10″ x 6′ 5”
1600 – Router with saw blade option: 14′ 6″ x 6′ 5”

Spindle Drive System:
24 HP stainless steel electrospindle (18Kw)
Variable speed up to 10,000 RPM
Liquid temperature controlled spindle with chiller to control temperature +/- 2oF Through-spindle water feed
Pneumatic draw bar
External water ring

Automatic Tool Changer:
1800 – 68 Station Dual Tool Rack (non-ITM); 1600 – 34 Station Tool Rack (non ITM)
Tool Connection: BT40 Quick Change Tool
Automatic Tool Cone Cleaning Between Tool Changes
“Protection Zone” software minimizes the chance for machine crashes caused by operator error.
“Quick Swap” feature allows pre-measured tools to be mounted in minutes, and makes the tool library virtually unlimited.
“Tool Shield” protects tools from debris and damage during operation.

Worktable:
Vacuum Part Holding System:
3 HP liquid ring vacuum pump, 5.1 SCFM @25 in Hg Individual vacuum control valves to each cup
“Air float” slab positioning

Vacuum Pods:
12 dual chamber vacuum cups: (2) 250mm x 500mm cups (4) 150mm X 150mm cups (6) 200mm X 200mm cups
2 manifolds, accommodates 8 vacuum cups each, total of 16 cups
TN20102
1800 – 16’ x 8’; 1600 16’ x 6’
Patent-pending ArmorDeckTM precision machined work surface with 30% more holding power will not corrode or dent, and ensures parts can’t move during fabrication. The mono-block machine base is exceptionally rigid and provides easy access during set up.
18” from floor to table top; step-up clear access
8” high x 18” wide ergonomic full length front step for easy loading and unloading
Page 1-41 © 2010, Park Industries
TITAN CNC Stone Center – Issue 1 – April 2010 – Section 1

Machine Specifications
Machine Control
Control Type:Siemens 840D open-architecture CNC control
15” color touch-screen operator controls
Windows XP Professional operating system
Solid-state hard drive
Video card with S-video and DVI ports
Parallel port, front and rear USB ports
Ethernet adapter
Handheld pendant
On-board Laser Digitizing System
Line and arc digitizing
Editing functions: rotate file, mirror file, zoom, tool compensation “Drip Feed” feature processes large program files directly from the hard drive Automatic tool compensation.
Z-axis spindle oscillation

Software and Hardware Packages:
Park Touchstone SFP (Shop Floor Programming) Software (included with machine):
Easy to use “conversational” touch-screen programming; CAD knowledge not required to operate system
Fully functional “on-machine” programming and digitizing CAM system

Equpped with:
Includes one year of software updates; updates after one year require an annual mainte- nance fee.
AlphaStone CAD/CAM software (optional)
Fully functional advanced CAD-CAM office programming system with bar code scanner
On-screen simulation of tool paths
Automatic tool grouping and tool path generation using styles
Includes one year of software updates; updates after one year require an annual mainte- nance fee.
AlphaCAD software (optional)
Fully functional advanced CAD programming system
PC Workstation (optional)
Computer tower, 17” LCD monitor, mouse and keypad Intel Core2 Duo 3Ghz processor
Windows version 7 64bit
500 GB 7200 rpm hard drive
4 GB memory
Page 1-42
© 2010, Park Industries
TN20102

TITAN CNC Stone Center – Issue 1 – April 2010 – Section 1
Machine Movements
X-Axis (Cross Travel Movement):
Length of movement: 15′ – 10″ spindle only
Length of movement: 14′ – 6″ spindle with saw option
Maximum speed: 2,360 inches per minute
Siemens AC servo motor with low backlash gearing, absolute encoder position feedback, and automatic lubricator
THK precision linear bearing system with seals, scrapers, lubricator, and zerk Precision ground helical rack & pinion drive with automatic lubrication Bellows protect positioning system from moisture, debris and grit
Y-Axis (Gantry Movement):
Length of movement: 1800 – 11′ 6″; 1600 – 7’ 6” Maximum speed: 2,360 inches per minute
Dual Siemens AC servo motors with low backlash gearing, absolute encoder position feed- back, automatic lubricator, and electronic synchronization
THK precision linear bearing system with seals, scrapers, lubricator, and zerk Precision ground helical rack & pinion drive with automatic lubrication Bellows protect positioning system from moisture, debris and grit
Z1-Axis (Spindle Rise and Lower Movement):
Length of movement: 12″
Maximum speed: 500 inches per minute
Siemens AC servo motor with absolute encoder position feedback Precision ground helical rack & pinion drive with automatic lubrication Bellows protect positioning system from moisture, debris and grit
Safety Features
Siemens Safety Rated Integrated Control
Full perimeter, safety-stop pull-cord assembly
Lockable 100 amp fused disconnect with Lock-out Tag-out procedure
Machine Construction Base Frame
TN20102
Park Industries’ StoneSpecTM “Mono-Bloc” unitized construction provides maximum rigidity and minimal foundation requirements.
Finite Element Analysis in the design process optimizes structural integrity
Welded machine components are stress-relieved prior to machining to ensure dimensional stability.
Precision machined at Park Industries’ factory utilizing the latest metalworking machine tool technology.
Page 1-43 © 2010, Park Industries

TITAN CNC Stone Center – Issue 1 – April 2010 – Section 1
Machine Specifications
Electrical, Air and Water Requirements Electrical Service Supply
480 volt (+/-10%), 3 phase, 60 Hz, 60 amps standard
60 amp fused disconnect between 480 volt power source and TITAN (disconnect supplied by customer)
Machine Internet Connection
DSL or high-speed internet connection hard-wired (not wireless) to machine.
Water Service Supply
NOTE: Water supply at machine connection point must be maintained at the following speci- fication to validate warranty. Park Industries is not responsible for premature or excessive corrosion nor any resulting failure to machines or their components caused by a shop’s water quality not maintained at the below required ranges. Water analysis is required prior to ma- chine installation!
pH: 8.0 to 8.5 range
Free Chlorine: 3 ppm maximum (If chlorine is used in your facility to manage bacte-
ria, it is always important to use the proper amount.)
Hardness: 50 to 300 ppm range
Total Alkalinity: 100 ppm minimum
Suspended Particle Size
◊ Spindle Center Water Feed: 10 micron maximum
◊ Spindle Water Ring: 50 micron maximum Dual water feed (two 3⁄4″ I.D. water lines minimum):
Spindle center water feed: 5 GPM, 45-65 PSI, filtered to 10 micron, and to above specification.
Optional blade, water ring, and vacuum pump: 7 GPM, 45-65 PSI, filtered to 50 mi- cron, and to the above specification.
Single water feed (one 3⁄4″ I.D. water line minimum): 12 GPM, 45-65 PSI, filtered to 10 micron and to the above specification.
Air (Pneumatic) Service Supply
Air specifications:
Line size: 1⁄2″ I.D
Min. Pressure: 100 psi
Required volume: 20 SCFM
Air Quality:
Particulate: 15 micron
Moisture: +37.4 deg. F Pressure Dewpoint @ 100psi
Oil: .01 mg/m3 Max.
Page 1-44
© 2010, Park Industries
TN20102

TN20102
Page 1-45 © 2010, Park Industries
TITAN CNC Stone Center – Issue 1 – April 2010 – Section 1
Machine Specifications
Space & Weight
Machine Weight:
1800 – 31,000 lbs; 1600 – 25,000 lbs.
Overall dimensions:
1800 Floor Space Requirements: 20′ long x 26′ wide x 7′ 8″ high (12′ 2″ high with optional overhead laser)
1600 Floor Space Requirements: 16′ long x 26′ wide x 7′ 8″ high (12′ 2″ high with optional overhead laser)
Exact layout and foundation drawings can be provided. (See machine foundation prints for greater detail, actual size may/will vary based on selected options)
Machine Options: Machine:
Sawing drive and pivot system – 3 HP, 360 degree rotation, 8″ maximum blade 480 volt (+/-10%), 3 phase, 60 Hz, 100 amps (standard)
208/240 volt, 45 KVA Transformer
575 volt, 45 KVA Transformer
Retractable water curtain for spindle and blade Retractable water curtain for spindle only
Water containment assembly, tank on front of table ArmorDeck Tabletop Planing Kit
Tool Setter
CNC Tool Kit
Projection laser assembly for part positioning (with mounting bracket)
Software and Hardware:
AlphaStone Standard Software AlphaStone – Additional Seat AlphaStone – Network License AlphaCAD Software
PC Workstation
Vacuum Pods Options:
Additional 150mm X 250mm vacuum fence
Additional 40mm X 150mm X 300mm support
Additional 120mm X 120mm square vacuum cup
Additional 150mm X 150mm square vacuum cup
Additional 200mm X 200mm square vacuum cup
Additional 250mm X 500mm square vacuum cup
Additional pin stop with laser target, 50mm vacuum base Additional portable manifold accommodates 8 vacuum cups each

TITAN CNC Stone Center – Issue 1 – April 2010 – Section 1
Machine Specifications
Machine Options: (cont’d) Other Options:
Water & air filters(24 month supply)
Water & air filters with tool clamping set and rotary water union (24 month supply) Basic tooling package
Laser Measurement System Hardware
Consumable Parts Kit
Spare Parts Kit
Additional Seat of Training, 5 day class at Park’s Training Center
AutoCad Training, 2 1/2 day class at Park’s Training Center (per seat)
90 day follow up 3 day training visit, includes travel expense
Extended two-year limited warranty (see Warranty Plan for details)
Park Industries Service & Support Included:
One-Year Limited Warranty (see Warranty Plan for details)
Five-Year Limited Warranty on Spindle (see Warranty Plan for details) “Next Day or No Pay” guaranteed parts plan
Detailed operator/maintenance manual with electrical schematics Domestic toll free 24/7 technical phone support
On-site domestic service available
Remote diagnostic capability
Diagnostic kit (includes dial indicator and electric test meter)
Professional instruction at Park Tech Center with classroom and hands-on machine training. Two seats of training are included with each machine purchase and must be redeemed within one year of installation.
Professional installation on customer site by Park Industries certified technician Pre-installation support with manual including shop layout
Customer-Responsible Items:
All machine requirements (reference Machine Electrical & Plumbing Requirements section)
Diamond tooling and abrasives
Tool holders
Building or suitable enclosure to prevent environmental damage (rain, wind, dust, temp) to the machine
Drain tubing routed into shop water system.
Quality concrete floor as indicated on foundation print
Customer will send up to two people for 5 to 10 business days (depending on options) of equip- ment operation & maintenance training at Park Tech Center in St. Cloud, Minnesota, prior to the shipment of the equipment; customer is responsible for trainee’s travel, lodging, meals, and other personal expenses.